60 deg. Rivets, Rivet tools, Countersinks and Drill bits For Sale

[MSG]

I have 60 deg. rivets for the 1917a1 & 1919:



1) Forward Top plate rivet, #7. I give you both the round head & 60 deg. countersunk rivets, so you can choose.
2) Rear Top plate rivet, #7.
3) Forward Cartridge stop.
4) Rear Cartridge stop rivet, #7.
5) Large Trunion rivets, 11/32”.
6) Bottom plate and Pintle pad rivets, 3/16”
7) Long Pintle pad rivet, 3/16”.

Countersinks and bits:

3/16 Cobalt 135 deg split point bit used for the small rivet holes.
#7 Cobalt 135 deg split point bit for the Top Plate and rear cartridge stop rivet holes.
11/32 Cobalt 135 deg split point drill bit used for drilling the large, trunion rivet holes.
No. 5, Cobalt, 60 deg. combined drill and countersink.

I have 9/16 and 5/8 HSS, 118 degree, 1/2 in shank, Silver and Deming drills. 4140 steel is tough on HSS, but if you're just enlarging a 9/16th hole, or the Cobalt 11/32 is used first to drill a pilot hole, this should get you done (with a little oil and patience). This is the same imported bit for which my local Lowe’s is getting $17.00.

and rivet setting tools:

I have 3 1/2" and 1 1/8" straight .401 shank rivet setting tools. With between 1/8 and 5/32 of the rivet shank protruding, these will make a rivet head very similar to the factory rivets. Experiment first of course. These are high alloy, heat-treated steel. Though designed for rivet guns, a large hammer (BFH) works too. There is also a fixture (center) available for setting rivets with a hydraulic press. It requires an additional 1" sleeve that must be purchased separately (see www.burntcapital.com for more information).

PRICES:

Rivets:

BHF-spec. 1917a1/1919 Rivets: $18.00, Free shipping.

Wrong Rivet Replacememt Kit: $11.00, Free shipping.

Includes proper #7 rivets, Front cartridge stop (1 - 4 above) and Cobalt #7 drill bit.

Package of 90 deg. commercial rivets for non-spec. Right side plates: $2.00 (with rivet set purchase, $4.00 if purchased alone)

For more information see: http://www.1919a4.com/forums/showthr...253#post184253

1917a1/1919 BHPB and Cam rivets: $10.00, Free shipping. See next post for more information.

M2/M3 Rivets: $27.50, Free shipping. See next post for more information.

FN 30 Rivets: $35.00

Drill Bit Packages: Shipping is included in package price.

4 bit set for my 60 degree, BHF-spec. rivets, or BlackBear rivets: $23.00

1 x 3/16 Cobalt 135 deg split point drill bit
1 x #7 (.2010) Cobalt 135 deg split point drill bit
1 x 11/32 Cobalt 135 deg split point drill bit
1 x 3/16 - 7/16 (No. 5) 60 deg. Cobalt combined drill and countersink

4 bit set for 90 degree rivets: $23.00

2 x 3/16 Cobalt 135 deg split point drill bit
1 x 11/32 Cobalt 135 deg split point drill bit
1 x 3/16 - 7/16 (No. 5) 90 deg. Cobalt combined drill and countersink

The Works: 4 bit set, Trunion hole bit, Rivet Setting tool & BHF-spec rivets: $65.00

Above 4 bit set plus Pintle hole bit (please specify 9/16 or 5/8, if you don't I'll ship a 5/8), 3 1/2"
rivet setting tool and my BHF-spec. rivets.

With a bit package or rivet order I will add the following items for:

Trunion hole drill bit: $14.00 (please specify 9/16" or 5/8")
#5 Cobalt Countersink: $14.00
3 1/2" Rivet setting tool: $12.00
1 1/2" Rivet setting tool: $13.00
Cobalt 3/16" drill bit: $2.50

Hydraulic press rivet setting fixture and tool: $28.00 (Sorry, material price increase)

GA residents add 7% sales tax (I don't charge it, I just collect it)

TO ORDER:

Please send check or money order to:

Burnt Capital Brands
Attn: M.S. Gorham
103 Garner Lane SE
Milledgeville, GA 31061-8866

Or order via PayPal, NOW ACCEPTING CREDIT CARDS and funds transfers. Make request to account:

msgorham@burntcapital.com

If you place an order through PayPal, be sure to complete the "Subject" and "Note" fields. Those fields must be completed to generate an order notification e-mail (If you don't do it, they don't tell me you placed an order)

For more information, please go to www.burntcapital.com

MSG

[MSG]

New item!

FN 30 Rivets: $35.00


For more information please see: http://www.1919a4.com/forums/showthr...842#post246842

60 Degree M2/M3 Rivets



Many people have asked me for M2/M3 rivets, so here they are.

1) 60 degree 3/16 x 11/16 (60)
2) Round head 5/32 x ½ (12)
3) 60 degree 3/16 x 1 3/16 (6)
4) Round head 3/16 x 2 ¾ (5)

These, like my 1919 rivets, are not Mil-spec. (those are a countersunk roundhead rivet), they are made for the home builder. The rear Top plate and Bottom plate, bottom front and bolt hold back rivets have a small 60-degree head so they can be bucked for peening like those in a 1919. The small 60-degree head means less of your Side plates wind up on the shop floor. The long Trunion rivets and 5/32” rivets have conventional pan heads. All rivets are a little long. Rivets can be shortened much easier than they can be lengthened (they can’t), so there is extra length to fill holes enlarged or otherwise boogered during the demil process. Extra rivets of all sizes are provided.

Price: $27.50 (I can’t in good conscience charge you more)


1917/1919 BHPB and Cam rivets



I’ve been asked for these in the past, but never offered them because I thought demand would be too small. Finally an opportunity presented itself that allowed me to split a production run. I now have them available for those of you building a 1917, or wanting to replace the BHPB or Cams. These were made using original 1919 drawings (thank you Rollin and Sam), but a little extra length has been added for the same reason as above. You need four of each, I give you six.

Price: $10.00 (Sorry, hassle factor)

For order information, see above.

MSG

[MSG]

Update. Orders for: Terry S., Isaac R., Wyatt R. and Matthew B. have been shipped, and should be in hand soon, if not already.

MSG

[TbcSEOD]

Got mine, and cant wait to get to using them

Thanks for the fair price, good quality and quick turn around!

~T

[MSG]

I’ll have a 60-degree set of rivets for the M2/M3 Machine gun, and 1919/1917 BHP bracket and cam rivets, available early January. For more information, please see:

http://www.1919a4.com/forums/showthr...844#post117844

MSG

[TeamDoh]

PM sent with quote request.

[MSG]

Sorry I didn't get this out Friday.

Update. Orders for: Jay S. (both of them), and Mark R. have been shipped, and should be in hand soon, if not already.

MSG

[MSG]

Update. Orders for: Donald H., Logan R., Brian P., Alan A., Lloyd P. and Drake have been shipped, and should be in hand soon, if not already.

MSG

[30calmachinegunner]

Michael, just wanted to say thanks for the fast shipping, got them a couple days ago. I just want to add that the rivet sets you have put together are the best I've used, thanks for everything.

[FloridaAKM]

PM sent for quote request on several items.